- 您现在的位置：买卖IC网 > Sheet目录510 > SI4731-D50-GM (Silicon Laboratories Inc)IC RADIO RECEIVER AM/FM 20-QFN
Si4730/31-D50
4.12. FM Hi-Cut Control
Hi-cut control is employed on audio outputs with
degradation of the signal due to low SNR and/or
multipath interference. Two metrics, SNR and multipath
interference, are monitored concurrently in forcing hi-cut
of the audio outputs. Programmable minimum and
maximum thresholds are available for both metrics. The
transition frequency for hi-cut is also programmable with
up to seven hi-cut filter settings. Attack and release
rates for hi-cut are programmable for both metrics from
a range of 2 ms to 64 s. The level of hi-cut applied can
be monitored with the FM_RSQ_STATUS command.
Hi-cut can be disabled by setting the hi-cut filter to audio
bandwidth of 15 kHz.
4.13. RDS/RBDS Processor (Si4731 Only)
The Si4731 implements an RDS/RBDS* processor for
symbol decoding, block synchronization, error
detection, and error correction.
The Si4731 device is user configurable and provides an
optional interrupt when RDS is synchronized, loses
synchronization, and/or the user configurable RDS
FIFO threshold has been met.
The Si4731 reports RDS decoder synchronization
status and detailed bit errors in the information word for
each RDS block with the FM_RDS_STATUS command.
The range of reportable block errors is 0, 1–2, 3–5, or
6+. More than six errors indicates that the
corresponding block information word contains six or
more non-correctable errors or that the block checkword
contains errors.
*Note: RDS/RBDS is referred to only as RDS throughout the
remainder of this document.
4.14. Tuning
The tuning frequency is directly programmed using the
FM_TUNE_FREQ and AM_TUNE_FREQ commands.
The Si4730/31 supports channel spacing steps of
10 kHz in FM mode and 1 kHz in AM mode.
4.15. Seek
The Si4730/31 uses RSSI, SNR, and AFC to qualify
stations. Most of these variables have programmable
thresholds for modifying the seek function according to
customer needs.
RSSI is employed first to screen all possible candidate
stations. SNR and AFC are subsequently used in
screening the RSSI qualified stations. The more
thresholds the system engages, the higher the
confidence that any found stations will indeed be valid
broadcast stations. The Si4730/31 defaults set RSSI to
a mid-level threshold and add an SNR threshold set to a
level delivering acceptable audio performance. This
trade-off will eliminate very low RSSI stations while
keeping the seek time to acceptable levels. Generally,
the time to auto-scan and store valid channels for an
entire FM band with all thresholds engaged is very short
depending on the band content. Seek is initiated using
the FM_SEEK_START command. The RSSI, SNR, and
AFC threshold settings are adjustable using properties.
4.16. Reference Clock
The Si4730/31 reference clock is programmable,
supporting RCLK frequencies listed in Table 11,
“Reference Clock and Crystal Characteristics,” on
page 15. Refer to Table 3, “DC Characteristics,” on
page 5 for switching voltage levels and Table 11 for
frequency tolerance information.
An onboard crystal oscillator is available to generate the
32.768 kHz reference when an external crystal and load
capacitors are provided. Refer to "2. Typical Application
Schematic" on page 16. This mode is enabled using the
POWER_UP command. Refer to “AN332: Si47xx
Programming Guide”.
The Si4730/31 performance may be affected by data
activity on the SDIO bus when using the integrated
internal oscillator. SDIO activity results from polling the
tuner for status or communicating with other devices
that share the SDIO bus. If there is SDIO bus activity
while the Si4730/31 is performing the seek/tune
function, the crystal oscillator may experience jitter,
which may result in mistunes, false stops, and/or lower
The Si4730/31 seek functionality
is performed
SNR.
completely on-chip and will search up or down the
selected frequency band for a valid channel. A valid
channel is qualified according to a series of
programmable signal indicators and thresholds. The
seek function can be made to stop at the band edge and
provide an interrupt, or wrap the band and continue
seeking until arriving at the original departure frequency.
The device sets interrupts with found valid stations or, if
the seek results in zero found valid stations, the device
indicates failure and again sets an interrupt. Refer to
“AN332: Si47xx Programming Guide”.
For best seek/tune results, Silicon Laboratories
recommends that all SDIO data traffic be suspended
during Si4730/31 seek and tune operations. This is
achieved by keeping the bus quiet for all other devices
on the bus, and delaying tuner polling until the tune or
seek operation is complete. The seek/tune complete
(STC) interrupt should be used instead of polling to
determine when a seek/tune operation is complete.
22
Rev. 1.0
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SI4737-C-EVB
BOARD EVAL SI4737 VERSION C
SI4743-C-EVB
BOARD EVALUATION FOR SI4743-C
SI4770-A-EVB
BOARD EVAL FOR CE AM/FM SI4770
SI4777-A20-GM
IC RCVR AM/FM CE HD-RADIO TUNER
SI4804CDY-T1-E3
MOSFET 2N-CH 30V 8A SO8
SI4808DY-T1-GE3
MOSFET N-CH/SCHOTTKY 30V 8SOIC
SI4812BDY-T1-GE3
MOSFET N-CH D-S 30V 8-SOIC
SI4814BDY-T1-GE3
MOSFET N-CH/SCHOTTKY 30V 8SOIC
相关代理商/技术参数
SI4731-D50-GMR
制造商:Silicon Laboratories Inc 功能描述:ADVANCED AM/FM RDS RECEIVER FOR MOBILE DEVICES - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC RADIO RECEIVER AM/FM 20-QFN 制造商:Silicon Laboratories Inc 功能描述:MOBLE DEV AM/FM/RCVR RDS 3X3X0.55 20P
SI4731-D60-EVB
功能描述:BOARD EVALUATION FOR SI473-D60 RoHS:是 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796
SI4731-D60-GM
功能描述:IC RADIO RX AM/FM/AUX 20QFN RoHS:是 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘
Si4731-D60-GMR
功能描述:射频接收器 BRDCAST AM/FM/AUXIN RADIO RECEIVER/RBDS RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
SI4731-D60-GU
功能描述:IC RADIO RX AM/FM/AUX 24SSOP RoHS:是 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘
Si4731-D60-GU2
制造商:SILABS 制造商全称:SILABS 功能描述:BROADCAST AM/FM/SW/LW RADIO RECEIVER
Si4731-D60-GUR
功能描述:射频接收器 BRDCAST AM/FM/AUXIN RADIO RECEIVER/RBDS RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
Si4731-Demo
功能描述:射频开发工具 Standalone Demo and Eval Board 3x3x0.55 RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V